DIY Chevron Canvas

So since I’m a crafty girl and I’m under 50, it’s no surprise I love chevron. Ha. Last year I painted this chevron canvas but it failed. I didn’t paint a white base coat, so my painted lines bled a bit, even with painters tape. My end product didn’t have the clean, straight edges you see here, which was a huge bummer since I meticulously measured and masked the entire canvas.

(Don’t worry! This post will turn from a sob story to success story very shortly!)

paint2paint1

Well, this week I finally got around to fixing up my canvas! I bought new white paint and carefully filled in the bleeding lines. It’s not absolutely stunning like the tutorial I followed (props to the original blogger, Jessica!), but I’m pretty happy with it. Now I have a cute and trendy decoration! I think I’ll set it out on my desk at work. Why not?

 I’m also going to fix up another failed wreath of mine. I’ll show you “before and after” pictures later this month. Well, that’s only if the “after” looks presentable. Have a great weekend, everyone!

Advertisements

DIY Homemade Coasters

So if you haven’t noticed, homemade coasters are all the rage right now. I’ve been inspired by a few different examples from Attic Lace, The Cottage Mama and Making Mondays blogs. I decided to make my own coasters out of a leftover calendar from one of my coworkers.

DSCF7351

This is my first time writing a full-blown tutorial, so I’m a little nervous about it. Let me know if I skip steps or don’t make any sense.

Also, I want to apologize ahead of time for not having artsty-I’m-a-blogger photos for this. The lighting was bad and I don’t have a fancy camera.

The supplies you’ll need:

  • A design for the surface of your coaster — calendars, photos, scrapbook paper, whatever you want.
  • 1 piece of scrap paper
  • Mod Podge
  • paint brushes
  • Four (4×4 inch) ceramic tiles (I found mine at Home Depot)
  • 1 sheet of craft felt
  • scissors
  • ruler
  • pencils and pens

Let’s get started! Do you have all your supplies lined up? Once you do, grab your scissors, pencil and ruler.

DSCF7331

DSCF7339

Measure, cut and draw a 3.75 x 3.75 inch square on a piece of scrap paper. This will be your pattern for the four coasters.

DSCF7334

Use the 3.75×3.75 in. pattern to trace and cut out squares on your calendar/scrapbook paper/photos for the surface of your coasters. Repeat three more times so you have four squares total.

DSCF7324

Now you’ll want to get your tile out. I wiped mine down with a wet rag just to make sure there wasn’t any dust or gunk on the surface.

IMG_20131103_215028_828 (1)

Place the tiles on a piece of newspaper so you don’t get globs all over your table (unless your an angel with a paint brush, I’m not). Brush one coat of Mod Podge over the surface of the clean ceramic tile.

I didn’t photograph this next part but if you keep reading /looking at photos it should make sense: Take your calendar cut-out and place it on the tile over the wet Mod Podge. Don’t rush! Smooth out the paper so there aren’t any bubbles or wrinkles.

IMG_20131103_215236_779

IMG_20131103_220104_003

Paint one coat of Mod Podge over the surface of the paper and tile.  Make sure you don’t have excessive clumps of Mod Podge on the rims of the tile. Try to make this coat as smooth as possible. Fast forward a little bit: Repeat these steps three more times so you have a total of four tiles drying.

IMG_20131103_220335_867

While your tiles are drying, you’ll want to measure and cut out a 3×3 inch square of craft felt. This will be the backing of your coasters. Repeat this step three times so you have a total of four 3×3 inch felt squares.

DSCF7347

DSCF7349

Once your tiles are dry, whip out your hot glue gun. Glue one felt square to the back of each tile. And again, repeat three more times so all four of your tiles are complete.

Tadaaaa! You have new coasters. Impressive, right?

DSCF7351

NOTE: I just want to give you a head up. I’ve used these coasters all week and I’ve noticed that my coffee mugs are sticking to the surface. I’m wondering if the Mod Podge isn’t glossy enough to be the top coat. Does anyone have any suggestions?

DIY Fall Wreath

I want to share with you a fall wreath I made last year. It was so easy to put together, I ended up making one for my mom too! Instead of giving you a step-by-step tutorial, feel free to check out the Crafting Mom blog where I got the inspiration.  I give that blogger, Jacki, credit for this great idea! I bought all of my supplies–the vine wreath, fall garland, craft felt and leaves–at Michaels for around $12 (gotta love those coupons).

fall_wreath

I added sparkly leaves to give my wreath a little shine and to make it slightly different from the original.

fall_wreath2

I’ve thought about making a winter version by spraying a twig wreath with white/silvery glitter and adding pine cones. Maybe I’ll tackle that in December… so come back again to see how it turns out.